安捷伦1260II高效液相色谱仪

    Agilent 1260 Infinity II 液相色谱系统 与新色谱柱技术和先进的备件相结合，可保证稳定可靠的分离和检测性能。1260 Infinity II 四元泵能够提供达 600 bar 的压力，完美适用于InfinityLab Poroshell 120 色谱柱。无脉冲、稳定而混合均匀的梯度可确保获得更的灵敏度和更可靠的结果，而较小的填料颗粒可实现更快速的分离和更的分离度。这款泵多支持四种溶剂，使您在自动溶剂混合中获得极灵活性，适用于各种研究和常规应用。稳定的材料能够耐受苛刻的应用，能够支持泵持续运行数年，从而大程度缩短停机时间并降低运行成本。 在分析生物样品或需要采用极端 pH 条件的应用中，可采用度耐腐蚀的钛金属四元泵。与其他 1260 Infinity II 生物惰性模块结合后，即可配置出安捷伦独有的包含完全无金属样品流路、且压力范围达 600 bar 的系统。 1260 Infinity II 容量柱温箱多可容纳四根 30 cm 色谱柱，并可通过 InfinityLab 快速更换切换阀直接操作每根色谱柱。无需断开并重新连接色谱柱即可自动运行不同方法。全部四根色谱柱均包含的固定式标签可记录色谱柱 ID 和完整使用历史，确保符合法规指南要求。色谱柱追踪也有助于避免重要序列运行过程中的故障，或避免固定相、溶剂和温度不匹配。 二极管阵列检测器的灵敏度流通池能够检测极低的样品浓度。我们还为二极管阵列检测器和荧光检测器提供了殊的生物惰性流通池，确保对生物样品实现安全的数据采集。

Physical Specifications Agilent 1260 Infinity II Isocratic Pump(G7110B)
安捷伦1260ⅡG7110B等度泵

Type	Specification	Comments
Weight	14.7 kg (32 lbs)
Dimensions (height × width × depth)	180 x 396 x 436 mm (7.1 x 15.6 x 17.2 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	80 VA, 65 W
Ambient operating temperature	4–55 °C (39–131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

 Physical Specifications Agilent 1260 Infinity II Quaternary Pump VL
(G7111A)
Table 2 Physical Specifications

Type	Specification	Comments
Weight	14.7 kg (32 lbs)
Dimensions (height × width × depth	180 x 396 x 436 mm (7.1 x 15.6 x 17.2 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	80 VA, 65 W
Ambient operating temperature	4–55 °C (39–131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

Type	Specification	Comments
Weight	14.7 kg (32 lbs)
Dimensions (height × width × depth	180 x 396 x 436 mm (7.1 x 15.6 x 17.2 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	80 VA, 65 W
Ambient operating temperature	4–55 °C (39–131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

Physical Specifications Agilent 1260 Infinity II Quaternary Pump
(G7111B)
Table 3 Physical Specifications

Type	Specification	Comments
Weight	14.7 kg (32 lbs)
Dimensions (height × width × depth)	180 x 396 x 436 mm (7.1 x 15.6 x 17.2 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	80 VA, 65 W
Ambient operating temperature	4–55 °C (39–131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

Physical Specifications Agilent 1260 Infinity II -G7102A Physical Specifications

Type	Specification	Comments
Weight	11 kg (non-cooled), 13 kg (cooled)
Dimensions (height × width × depth)	415 x 200 x 450 mm (16.3 x 7.9 x 17.7 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	150 W (max)	Maximum
Ambient operating temperature	10–35 °C (50–95 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 80 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 2000 m (6562 ft)
Non-operating altitude	Up to 4600 m (15091 ft)	For storing the module
Safety standards: IEC, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.

Performance Specification of the ELS Detector

Type	Specification
Light Source
G7102A	LASER 405 nm, 10 mW (Class 3B)
Detector	Dual PMT with digital signal processing
Nebuliser	OFF, 25 – 90 °C
Evaporator
Non-cooled	OFF, 25 – 120 °C
Cooled	OFF, 10 – 80 °C
Gas Flow Range	0.9 – 3.25 SLM (controlled gas shut-off)
Short Term Noise	<0.1 mV under specified condtions. See “Specification Conditions” on page 24.
Drift	<1 mV/h under specified condtions. See “Specification Conditions” on page 24.
Operating Pressure	60 – 100 psi (4.1 – 6.9 bar)
Eluent Flow range	0.2 – 5.0 mL/min
Digital Output	10, 40 or 80 Hz (24 bit)

 G7114B  Physical Specifications

Type	Specification	Comments
Weight	11 kg (24.3 lbs)
Dimensions (height × width × depth)	140 x 396 x 436 mm (5.5 x 15.6 x 17.2 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	80 VA, 70 W
Ambient operating temperature	4 - 55 °C (39 - 131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

Agilent 1260 Infinity II Variable Wavelength Detector (G7114A) Performance Specifications

Feature	Specification
Detection type	Double-beam photometer
Light source	Deuterium lamp
Number of signals	Single and dual wavelength detection
Maximum data rate	120 Hz (single wavelength detection) 2.5 Hz (dual wavelength detection)
Noise	<±0.25·10-5 AU, at 230 nm (single wavelength detection) <±0.80·10-5 AU, at 230 nm and 254 nm (dual wavelength detection)
Drift	<1·10-4 AU/h, at 230 nm
Linearity	>2.5 AU upper limit
Wavelength range	190 – 600 nm
Wavelength accuracy	±1 nm, self-calibration with deuterium lines, verification with holmium oxide filter
Wavelength precision	<±0.1 nm
Slit width	6.5 nm typical over whole wavelength range
Time programmable	Wavelength, polarity, peak width, lamp on/off
Flow cells	Standard: 14 μL volume, 10 mm cell path length and 40 bar (588 psi) pressure maximum Micro: 2 μL volume, 3 mm cell path length and 120 bar (1760 psi) pressure maximum Semi-micro: 5 μL volume, 6 mm cell path length and 40 bar (588 psi) pressure maximum Preparative: 4 μL volume, 3 mm cell path length and 120 bar (1760 psi) pressure maximum Preparative: 0.3 mm cell path length and 50 bar (725 psi) pressure maximum Preparative: 0.06 mm cell path length and 50 bar (725 psi) pressure maximum High pressure: 14 μL volume, 10 mm cell path length and 400 bar (5801 psi) pressure maximum
Spectral tools	Stop-flow wavelength scan
Analog output	Recorder/Integrator 100 mV or 1 V, 1 output
Communication	LAN, Controller-area network (CAN), ERI: ready, start, stop and shut-down signals, USB
GLP	Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of lamp burn time with user settable limits and feedback messages. Electronic records of maintenance and errors. RFID for electronics records of flow cell and UV lamp conditions (path length, volume, product number, serial number, test passed, and usage). Verification of wavelength accuracy with built-in holmium oxide filter.
Safety and maintenance	Extensive diagnostics, error detection and display through Agilent Instant Pilot and Agilent Lab Advisor software. Leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas. Tracking of flow cells and lamps with RFID (radio frequency identification) tags

Physical Specifications G7115A

Type	Specification	Comments
Weight	12 kg (26.5 lbs)
Dimensions (height × width × depth)	140 x 396 x 436 mm (5.5 x 15.6 x 17 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	110 VA / 100 W
Ambient operating temperature	4–55 °C (39–131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

Performance Specifications G7115A

Type	Specification	Comments
Detection type	1024-element photodiode array
Light source	Deuterium and tungsten lamps	The UV-lamp is equipped with RFID tag that holds lamp typical information.
Data rate	up to 120 Hz
Wavelength range	190 – 950 nm
Short term noise (ASTM) Single and Multi-Wavelength	< ± 0.7·10-5 AU at 254 and 750 nm	see "Specification Conditions" below
Drift	< 0.9·10-3 AU/h at 254 nm	see "Specification Conditions" below
Linear absorbance range	> 2 AU (5 %) at 265 nm	see "Specification Conditions" below
Wavelength accuracy	± 1 nm	Self-calibration with deuterium lines, verification with holmium oxide filter
Wavelength bunching	1 – 400 nm	Programmable in steps of 1 nm
Slit width	1, 2, 4 , 8, 16 nm	Programmable slit
Diode width	< 1 nm
Flow cells	Standard: 13 μL volume, 10 mm cell path length and 120 bar (1740 psi) pressure maximum Standard bio-inert: 13 μL volume, 10 mm cell path length and 120 bar (1740 psi) pressure maximum Semi-micro: 5 μL volume, 6 mm cell path length and 120 bar (1740 psi) pressure maximum Micro: 2 μL volume, 3 mm cell path length, 120 bar (1740 psi) pressure maximum Semi-nano: 500 nL volume, 10 mm cell path length and 50 bar (725 psi) pressure maximum Nano: 80 nL volume, 6 mm cell path length and 50 bar (725 psi) pressure maximum High pressure: 1.7 μL volume, 6 mm cell path length and 400 bar (5800 psi) pressure maximum Prep SST: 3 mm cell path length and 120 bar (1740 psi) pressure maximum Prep Quartz:0.3 mm cell path length and 20 bar (290 psi) pressure maximum Prep Quartz: 0.06 mm cell path length and 20 bar (290 psi) pressure maximum	All flow cells are equipped with RFID tags that hold cell typical information. pH range 1.0 – 9.5 (12.5 solvent dependent with bio-inert version
Time programmable	Wavelength, polarity, peak width, lamp bandwidth, autobalance, wavelength range, threshold, spectra storage mode
Spectral tools	Data analysis software for spectra evaluation, including spectral libraries and peak purity functions
Control and data evaluation	Agilent OpenLab CDS	• OpenLab CS C.01.07 • Driver A.02.14

Agilent 1260 Infinity II Variable Wavelength Detector (G7116A) Physical Specifications

Type	Specification	Comments
Weight	12.5 kg (27.6 lbs)
Dimensions (height × width × depth)	160 x 435 (472*) x 436 mm (6.3 x 17.1 (18.6*) x 17.2 inches) *with column ID kit
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	150 VA, 150 W
Ambient operating temperature	4–55 °C (39–131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

Agilent 1260 Infinity II Multicolumn Thermostat (G7116A) Performance Specifications

Feature	Specification1
Operating principle	Thermostatted column compartment with dual, independent Peltier-element. Solvent pre-heating and still-air operation for reduction of chromatographic band-broadening under UHPLC-conditions.
Temperature range	10 °C below ambient (minimum 4 °C) to 85 °C settable in steps of 0.1 K
Temperature stability	±0.1 °C
Temperature accuracy	±0.5 °C (with calibration for 40 °C)
Temperature precision	0.05 °C
Independent Temperature zones	2in single device
Column capacity	4 columns of up to 300 mm length plus A-Line Quick-Connect fittings or pre-column Number of pre column Quick-Connect Heat Exchangers is scalable – each column can be equipped with individual heat exchanger for best performance 4-column selector valve is available to access each column without replumbing
Heat-up/cool-down time	5 min from ambient to 40 °C 10 min from 40 °C to 20 °C <25 min from 25 °C to 85 °C
Solvent heat exchangers	For pre-column solvent heating, G7116A is equipped with a Quick-Connect Heat Exchanger Large ID (0.17 mm capillary, 3 μL internal volume) as default. Other dimensions of Quick-Connect Heat Exchangers are optionally available as well as heat exchangers made out of bio-inert materials (metal-free).
Valve options	1 x integrated valve drive as option to host user-exchangeable Quick-Change valve heads (up to 600 bar) of different formats: 2-position/6-port, 2-position/10-port, 4-column selection. Also available in bio-inert materials. Valve heads are automatically identified by their tag.
Column identification	Optionally, column identification kit to track history of up to four columns. Mounted left hand-side of module.
Communications	Controller-area network (CAN). G7116A is a hosted module (LC stack needs to contain a LAN communication and control card)
Software compatibility	Requires OpenLAB CDS A.01.03 - A.02.02 (with LC & CE Drivers A.02.14) ?昈penLAB CDS ChemStation ed. C.01.03 -C.01.07 SR2 or higher ?OpenLAB CDS EZChrom ed. A.04.05 - A.04.07 SR2 or higher MassHunter (LC Drivers A.02.14) ?MassHunter B.07.01 or higher for (Q)-TOF ?MassHunter B.08.02 or higher for QQQ
Safety and maintenance	Extensive diagnostics, error detection and display (through Instant Pilot control module and Agilent LabAdvisor), leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in main maintenance areas.
GLP	Valve heads carrying tags with serial number, pressure rating, number of switches and valve type. Concept of column identification.

Agilent 1260 Infinity II Variable Wavelength Detector (G7117A) Physical Specifications

Type	Specification	Comments
Weight	11.5 kg (25.4 lbs)
Dimensions (height × width × depth)	140 x 396 x 436 mm (5.5 x 15.6 x 17.2 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	110 VA, 100 W
Ambient operating temperature	4 – 40 °C (39 – 104 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

Agilent 1260 Infinity II Variable Wavelength Detector (G7117A) Performance Specifications

Feature	Specification
Detector type	1024-element diode array
Light source	Deuterium
Number of signals	8
Maximum sampling rate	120 Hz (both spectra and signals)
Short-term noise	with 10 mm Max-Light cartridge cell: <±3·10-6 AU at 230/4 nm, slit width 4 nm, TC 2 s, ASTM with 60 mm Max-Light cartridge cell: <±0.6·10-6 AU/cm at 230/4 nm, slit width 4 nm, TC 2 s, ASTM
Drift	<0.5·10-3 AU/h at 230 nm
Linearity	>2.0 AU (5 %) at 265 nm Typically 2.5 AU (5 %)
Wavelength range	190 – 640 nm
Wavelength accuracy	±1 nm, self-calibration with deuterium lines
Wavelength precision	<±0.1 nm
Diode width	~0.5 nm
Wavelength bunching	Programmable, 2 – 400 nm, in steps of 1 nm
Flow cells	User-exchangeable, self-aligning cartridge cells with RFID tags. Max-Light Cartridge Cell (Standard): 10 mm, σV = 1.0 μL Max-Light Cartridge Cell (High Sensitivity): 60 mm, σV = 4 μL Max-Light Cartridge Ultra Low Dispersion (ULD) Cell: 10 mm, σV = 0.6 μL Max-Light Cartridge High Dynamic Range (HDR) Cell: 3.7 mm, σV = 0.8 μL Maximum Operating Pressure (MOP)1: 70 bar Maximum Incidental Pressure (MIP)2: 150 bar
Spectral tools	Data analysis software for spectra evaluation, including spectral libraries and peak purity functions
Analog output	Recorder/integrator: 100 mV or 1 V, output range 0.001 – 2 AU, one outpu
Communications	LAN, controller-area network (CAN), ERI: ready, start, stop and shut-down signals USB
GLP features	RFID for electronics records of flow cell and UV lamp conditions (path length, volume, product number, serial number, test passed, usage) Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of lamp burn time with user settable limits and feedback messages. Electronic records of maintenance and errors. Verification of wavelength accuracy with deuterium lines.
Safety and maintenance	Extensive diagnostics, error detection and display through Agilent Instant Pilot and Agilent Lab Advisor software. Leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas.
Others	Second generation of Electronic temperature control (ETC) for the complete optical unit

Agilent 1290 Infinity II Diode Array Detector (G7117B) Performance Specifications

Feature	Specification
Detector type	1024-element diode array
Light source	Deuterium
Number of signals	8
Maximum sampling rate	240 Hz (both spectra and signals)
Short-term noise	with 10 mm Max-Light cartridge cell: <±3·10-6 AU at 230/4 nm, slit width 4 nm, TC 2 s, ASTM with 60 mm Max-Light cartridge cell: <±0.6·10-6 AU/cm at 230/4 nm, slit width 4 nm, TC 2 s, ASTM
Drift	<0.5·10-3 AU/h at 230 nm
Linearity	>2.0 AU (5 %) at 265 nm Typically 2.5 AU (5 %)
Wavelength range	190 – 640 nm
Wavelength accuracy	±1 nm, self-calibration with deuterium lines
Wavelength precision	<±0.1 nm
Slit width	Programmable: 1, 2, 4, 8 nm
Diode width	~0.5 nm
Wavelength bunching	Programmable, 2 – 400 nm, in steps of 1 nm
Spectral tools	Data analysis software for spectra evaluation, including spectral libraries and peak purity functions
Flow cells	User-exchangeable, self-aligning cartridge cells with RFID tags. Max-Light Cartridge Cell (Standard): 10 mm, σV = 1.0 μL Max-Light Cartridge Cell (High Sensitivity): 60 mm, σV = 4 μL Max-Light Cartridge Ultra Low Dispersion (ULD) Cell: 10 mm, σV = 0.6 μL Max-Light Cartridge High Dynamic Range (HDR) Cell: 3.7 mm, σV = 0.8 μL Maximum Operating Pressure (MOP)1: 70 bar Maximum Incidental Pressure (MIP)2: 150 bar
Analog output	Recorder/integrator: 100 mV or 1 V, output range 0.001 – 2 AU, one output
Communications	LAN, controller-area network (CAN), ERI: ready, start, stop and shut-down signals, USB
GLP features	RFID for electronics records of flow cell and UV lamp conditions (path length, volume, product number, serial number, test passed, usage) Early maintenance feedback (EMF) for continuous tracking of instrument usage in terms of lamp burn time with user settable limits and feedback messages. Electronic records of maintenance and errors. Verification of wavelength accuracy with deuterium lines.
Safety and maintenance	Extensive diagnostics, error detection and display through Agilent Instant Pilot and Agilent Lab Advisor software. Leak detection, safe leak handling, leak output signal for shutdown of pumping system. Low voltages in major maintenance areas.
Others	Second generation of Electronic temperature control (ETC) for the complete optical unit

Agilent 1290 Infinity II High Speed Pump (G7120A) Physical Specifications

Type	Specification	Comments
Weight	21.0 kg (46.3 lbs)
Dimensions (height × width × depth)	200 x 396 x 436 mm (7.9 x 15.6 x 17.2 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	210 VA / 180 W
Ambient operating temperature	4 – 55 °C (39 – 131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.

Agilent 1290 Infinity II High Speed Pump (G7120A) Performance Specifications

Feature	Specification
Hydraulic system	Two dual pistons in series, pumps with proprietary servo-controlled variable stroke design and smooth motion control.
Pump resolution step size	300 pL step size
Settable flow range	0.001 – 5 mL/min, in 0.001 mL/min increments (executed in 300 pL/step increments).
Flow precision	≤0.07 % RSD or 0.005 min SD, whatever is greater
Flow accuracy	±1 % or 10 μL/min, whatever is greater
Pressure range	up to 130 MPa (1300 bar) at 0 – 2 mL/min ramping down to 80 MPa (800 bar) at 5 mL/min
Pressure pulsation	<1 % amplitude or <0.5 MPa (5 bar), whatever is greater
Compressibility compensation	Automatic
Recommended pH-range	1.0 – 12.5, solvents with pH <2.3 should not contain acid which attack stainless steel.
Gradient formation	High pressure binary mixing
Delay volume	As low as 45 μL (10 μL without mixer)
Composition precision	<0.15 % RSD or 0.01 min SD, whatever is greater
Composition accuracy	±0.35 % absolute
Number of solvent	2 out of maximum 26 solvents
Solvent selection valve	Internal 4-solvent selection valve included. External 2x 12 solvent valve as option, fully integrated in the pump control interface.

Agilent 1290 Infinity II High Speed Pump (G7120A) Performance Specifications

Feature	Specification
Hydraulic system	Two dual pistons in series, pumps with proprietary servo-controlled variable stroke design and smooth motion control.
Pump resolution step size	300 pL step size
Settable flow range	0.001 – 5 mL/min, in 0.001 mL/min increments (executed in 300 pL/step increments).
Flow precision	≤0.07 % RSD or 0.005 min SD, whatever is greater
Flow accuracy	±1 % or 10 μL/min, whatever is greater
Pressure range	up to 130 MPa (1300 bar) at 0 – 2 mL/min ramping down to 80 MPa (800 bar) at 5 mL/min
Pressure pulsation	<1 % amplitude or <0.5 MPa (5 bar), whatever is greater
Compressibility compensation	Automatic
Recommended pH-range	1.0 – 12.5, solvents with pH <2.3 should not contain acid which attack stainless steel.
Gradient formation	High pressure binary mixing
Delay volume	As low as 45 μL (10 μL without mixer)
Composition precision	<0.15 % RSD or 0.01 min SD, whatever is greater
Composition accuracy	±0.35 % absolute
Number of solvent	2 out of maximum 26 solvents
Solvent selection valve	Internal 4-solvent selection valve included. External 2x 12 solvent valve as option, fully integrated in the pump control interface.

Type	Specification
Weight	11.9 kg (26.2 lbs)
Dimensions (height × width × depth)	140 x 396 x 436 mm (5.5 x 15.6 x 17.0 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	70 VA, 60 W
Ambient operating temperature	4-55 °C (39-131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

G7121A Physical Specifications

Type	Specification
Weight	11.9 kg (26.2 lbs)
Dimensions (height × width × depth)	140 x 396 x 436 mm (5.5 x 15.6 x 17.0 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	70 VA, 60 W
Ambient operating temperature	4-55 °C (39-131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

Performance Specifications Agilent 1260 Infinity II Fluorescence Detector
SPECTRA (G7121B)

Type	Specification	Comments
Detection type	Multi-signal fluorescence detector with rapid on-line scanning capabilities and spectral data analysis
Performance specifications	Single wavelength operation: • RAMAN (H2O) > 500 (noise reference measured at signal) Ex=350 nm, Em=397 nm, dark value 450 nm, standard flow cell • RAMAN (H2O) > 3000 (noise reference measured at dark value) Ex=350 nm, Em=397 nm, dark value 450 nm, standard flow cell Dual wavelength operation: RAMAN (H2O) > 300 Ex 350 nm, Em 397 nm and Ex 350 nm, Em 450 nm, standard flow cell.	Reference conditions: Standard cell 8 μL, response time 4 s, HPLC-grade water and restriction capillary. For details refer to the Service Manual.
Light source	Xenon Flash Lamp, normal mode 20 W, economy mode 5 W, lifetime 4000 h
Pulse frequency	296 Hz for single signal mode 74 Hz for economy mode
Maximum data rate	74 Hz, 148 Hz
Excitation monochromator	Range: settable 200 nm - 1200 nm and zero-order Bandwidth: 20 nm (fixed) Monochromator: concave holographic grating, F/1.6, blaze: 300 nm
Emission monochromator	Range: settable 200 nm - 1200 nm and zero-order Bandwidth: 20 nm (fixed) Monochromator: concave holographic grating, F/1.6, blaze: 400 nm
Reference system	in-line excitation measurement
Timetable programing	up to 4 signal wavelengths, response time, PMT Gain, baseline behavior (append, free, zero), spectral parameters
Spectrum acquisition	Excitation or Emission spectra Scan speed: 28 ms per datapoint (e.g. 0.6 s/spectrum 200 – 400 nm, 10 nm step) Step size: 1 – 20 nm Spectra storage: All
Wavelength characteristic	Repeatability +/- 0.2 nm Accuracy +/- 3 nm setting
Flow cells	Standard: 8 μL volume and 20 bar (2 MPa) pressure maximum, fused silica block Optional: • Bio-inert: 8 μL volume and 20 bar (2 MPa) pressure maximum, (pH 1–12) • Micro: 4 μL volume and 20 bar (2 MPa) pressure maximum
Control and data evaluation	Agilent ChemStation for LC, Agilent Instant Pilot G4208A with limited spectral data analysis and printing of spectra

G7129AB Physical Specifications

Type	Specification	Comments
Weight	19 kg (41.9 lbs)	w/o sample cooler
Dimensions (height × width × depth)	324 x 396 x 468 mm (12.8 x 15.6 x 18.4 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	350 VA / 350 W / 1195 BTU/h
Ambient operating temperature	4 - 40 °C (39 - 104 °F), without chiller up to 55 °C (131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)1	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11
Permitted solvents	Boiling point ≥56 °C Auto-ignition temperature ≥200 °C

Performance Specifications (G7129A)

Type	Specification	Comment
Injection range	0.1 – 100 μL in 0.1 μL increments with 100 μL up to 60 MPa 0.1 – 900 μL in 0.1 μL increments with 900 μL up to 40 MPa	Up to 1800 μL with multiple draw (hardware modification required) Requires 900 μL analytical head
Precision	<0.25 % RSD of peak areas from <5 μL to 100 μL	Measured caffeine
Pressure range	0 – 60 MPa (0 – 600 bar, 0 – 8702 psi) 0 – 40 MPa (0 – 400 bar, 0 – 5801 psi)	for 900 μL Analytical Head
Sample viscosity range	0.2 – 5 cp
Sample capacity	132 x 2 mL vial (two trays default) 100 x 2 mL vial (two classic trays optional) 36 x 6 mL vials (two trays optional)
Carry over	<0.004 % (40 ppm) with needle wash	Using the following conditions: • ZORBAX Eclipse Plus C18, RRHD, 2.1 x 50 mm, 1.8 μm (959757-902) • Mobile Phase: • A: 0.1 % TFA in water • B: 0.1 % TFA in acetonitrile • Isocratic : % B=33 % • Flow rate: 0.5 mL/min • Column temperature: 50 °C • Wavelength detection: 257/4 nm, ref. wavelength 380/100 nm, 20 Hz • Injection volume: 1 μL • Sample: 1200 ng/μL Chlorhexidine for UV, (dissolved with mobile phase A), 1 μL injected and measured both on Agilent G7117B DAD • Wash solution: H2O with 0.1 % TFA (5 s)
Injection cycle time	18 s for draw speed 200 μL/min Ejection speed: 200 μL/min Injection volume: 1 μL
Minimum sample volume	1 μL from 5 μL sample in 100 μL microvial, or 1 μL from 10 μL sample in 300 μL microvial.	Needle height offset has to be adapted to ensure that needle doesn’t touch vial bottom. Default needle height = 0 equates to 2 mm above the vial bottom.
Control and data evaluation	Agilent OpenLab CDS MassHunter QQQ MassHunter TOF/QTOF Lab Advisor ICF for 3rd party SW control LC and CE Drivers	A.02.02 or above B.08.01 or above B.07.02 or above B.02.07 or above A.02.04 or above A.02.12 or above
Local control	Agilent Instant Pilot (G4208A)	B.02.17 or above
Communications	Controller-area network (CAN),Local Area Network (LAN) ERI: ready, start, stop and shut-down signals
Safety and maintenance	Extensive support for troubleshooting and maintenance is provided by the Instant Pilot, Agilent Lab Advisor, and the Chromatography Data System. Safety-related features are leak detection, safe leak handling, leak output signal for shutdown of pumping system, and low voltages in major maintenance areas.
GLP features	Early maintenance feedback (EMF) for continuous tracking of instrument usage with user-settable limits and feedback messages. Electronic records of maintenance and errors
Housing	All materials recyclable.
Metering device	Metering device in high pressure flow path

Performance Specifications (G7129B)

Type	Specification	Comment
Injection range	0.1 – 20 μL in 0.1 μL increments (default) 0.1 – 40 μL in 0.1 μL increments if 40μL loop is installed 0.1 – 120 μL in 0.1 μL increments with 1290 Infinity large volume injection kit (hardware modification required) 0.1 – 100 μL in 0.1 μL (if 100 μL-loop and 100 μL-head is installed)	Up to 1500 μL with 1400 μL-multi-draw kit and 100 μL-analytical head up to 130 MPa (1300 bar, 18854 psi) up to 60 MPa (600 bar, 8702 psi)
Precision	<0.25 % RSD of peak areas from 5 μL to 100 μL	Measured caffeine
Pressure range	Up to 130 MPa (1300 bar, 18854 psi)
Sample viscosity range	0.2 – 5 cp
Sample capacity	132 x 2 mL vial (two trays default) 100 x 2 mL vial (two classic trays optional) 36 x 6 mL vials (two trays optional)
Carry over	<0.004 % (40 ppm) with needle wash	Using the following conditions: • ZORBAX Eclipse Plus C18, RRHD, 2.1 x 50 mm, 1.8 μm (959757-902) • Mobile Phase: • A: 0.1 % TFA in water • B: 0.1 % TFA in acetonitrile • Isocratic : % B=33 % • Flow rate: 0.5 mL/min • Column temperature: 50 °C • Wavelength detection: 257/4 nm, ref. wavelength 380/100 nm, 20 Hz • Injection volume: 1 μL • Sample: 1200 ng/μL Chlorhexidine for UV, (dissolved with mobile phase A), 1 μL injected and measured both on Agilent G7117B DAD • Wash solution: H2O with 0.1 % TFA (5 s)
Injection cycle time	18 s for draw speed 200 μL/min Ejection speed: 200 μL/min Injection volume: 1 μL
Minimum sample volume	1 μL from 5 μL sample in 100 μL microvial, or 1 μL from 10 μL sample in 300 μL microvial.	Needle height offset has to be adapted to ensure that needle doesn’t touch vial bottom. Default needle height = 0 equates to 2 mm above the vial bottom.
Control and data evaluation	Agilent OpenLab CDS MassHunter QQQ MassHunter TOF/QTOF Lab Advisor ICF for 3rd party SW control LC and CE Drivers	A.02.02 or above B.08.01 or above B.07.02 or above B.02.07 or above A.02.04 or above A.02.12 or above
Local control	Agilent Instant Pilot (G4208A)	B.02.17 or above
Communications	Controller-area network (CAN),Local Area Network (LAN) ERI: ready, start, stop and shut-down signals
Safety and maintenance	Extensive support for troubleshooting and maintenance is provided by the Instant Pilot, Agilent Lab Advisor, and the Chromatography Data System. Safety-related features are leak detection, safe leak handling, leak output signal for shutdown of pumping system, and low voltages in major maintenance areas.
GLP features	Early maintenance feedback (EMF) for continuous tracking of instrument usage with user-settable limits and feedback messages. Electronic records of maintenance and errors.
Housing	All materials recyclable.
Metering device	Metering device in high pressure flow path

Physical Specifications （G7162A）

Type	Specification	Comments
Weight	15 kg (33 lbs)
Dimensions (height × width × depth)	180 x 396 x 436 mm (7.1 x 15.6 x 17.2 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	70 W / 80 VA
Ambient operating temperature	4–55 °C (39–131 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

Physical Specifications Agilent 1260 Infinity II Multisampler
(G7167B)

Type	Specification	Comments
Weight	22 kg (48.5 lbs)	w/o sample cooler
Dimensions (height × width × depth)	320 x 396 x 468 mm (12.6 x 15.6 x 18.4 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	180 VA, 180 W
Ambient operating temperature	4 - 40 °C (39 - 104 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11
Permitted solvents	Boiling point ≥56 °C Auto-ignition temperature ≥200 °C

Physical Specifications Agilent 1260 Infinity II Bio-inert
Multisampler (G5668A)

Type	Specification	Comments
Weight	22 kg (48.5 lbs)	w/o sample cooler
Dimensions (height × width × depth)	320 x 396 x 468 mm (12.6 x 15.6 x 18.4 inches)
Line voltage	100 – 240 V~, ± 10 %	Wide-ranging capability
Line frequency	50 or 60 Hz, ± 5 %
Power consumption	180 VA, 180 W
Ambient operating temperature	4 - 40 °C (39 - 104 °F)
Ambient non-operating temperature	-40 – 70 °C (-40 – 158 °F)
Humidity	< 95 % r.h. at 40 °C (104 °F)	Non-condensing
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15092 ft)	For storing the module
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11
Permitted solvents	Boiling point ≥56 °C Auto-ignition temperature ≥200 °C

Table 3 Agilent 1290 Infinity II Multisampler (G7167B) Performance Specifications

Type	Specification	Comment
Injection range for Single-needle instruments	Default: 0.1 – 20 μL in 0.1 μL increments; optional: 40 μL or 100 μL (using 100 μL analytical head)	Up to 1300 bar using 40 μL (default) or optional 100 μL analytical head
	Pressure range up to 400 bar due to 900 μL analytical head	Pressure range up to 400 bar due to 900 μL analytical head
	0.1 – 500 μL or 900 μL in 0.1 μL increments (using 900 μL analytical head)	Pressure range up to 1300 bar Multi-draw modus (Injection into needle-seat capillary
Injection range for Dual-needle instruments	Default: 0.1 – 20 μL in 0.1 μL increments; optional: 40 μL or 100 μL	Up to 1300 bar using 100 μL analytical head
	Up to 500 μL in 0.1 μL increments depending on installed loop size	Up to 1300 bar using 100 μL analytical head + Multi-load
Precision for Single-needle instruments	<0.15 % RSD or SD <10 nL, whatever is greater	Measured caffeine
Precision for Dual-needle instruments	<0.2 % RSD or SD <10 nL, whatever is greater	Measured caffeine
Pressure range	Up to 1300 bar (G7167B)	Max pressure for basic instrume
Sample viscosity range	0.2 – 5 cp	Max. 6144/1536 samples (384MTP/96)
Sample capacity	1H Drawer up to 8 drawers and 16 positions Shallow well plates (MTP)	3072 samples, 432 vials (2 mL)
	2H Drawer up to 4 drawers and 8 positions MTP, deep well plates, vials, Eppendorf	1536 samples, 60 vials (6 mL), 384 vials (1 mL), 216 vials (2 mL)
	3H Drawer up to 2 drawers and 4 positions MTP, deep well plates, vials up to 6 mL, Eppendorf	Using standard Single-needle setup
		Time between 2 injections is not mechanically limited, time delay depends on communication speed of software, OS or network connections
Carry Over	<0.003 % (30 ppm) Multisampler Standard and Dual Needle <0.0009 % (9 ppm) Multisampler Multiwash	Using the following conditions: • Column: Agilent Pursuit XRs 3 C18, 2.0 x 50 mm • Mobile phase: • A: 0.1 % TFA in water • B: 0.1 % TFA in Acetonitrile • Isocratic : % B=40 % • Flow rate: 0.5 mL/min • Temperature: 25 °C • Wavelength: 257 nm • Sample: 1200 ng/μL Chlorhexidine (dissolved with mobile phase A), 1 μL injected and measured on G4212A DAD • Wash solution: H2O with 0.1 % TFA (3 s)
Multiwash	Outer needle wash and seat backflush for carryover reduction with up to 3 different solvents
Control and data evaluation	Agilent Open Lab CDS	A.02.01 or above (A.02.02 supports Sample Entry UI)
	MassHunter QQQ	B.07.00 SP11 or above
	MassHunter QTOF	B.05.01 SP31 or above
	Lab Advisor	B.02.05 or above
	ICF for 3rd party SW control	A.02.01 or above
	LC and CE Drivers	A.02.10 or above
Local Control	Agilent Instant Pilot (G4208A)	B.02.17 or above (currently not supported/official release 2015)
Communications	Controller-area network (CAN), Local Area Network (LAN) ERI: ready, start, stop and shut-down signals
Safety and maintenance	Extensive support for troubleshooting and maintenance is provided by the Instant Pilot, Agilent Lab Advisor, and the Chromatography Data System. Safety-related features are leak detection, safe leak handling, leak output signal for shutdown of pumping system, and low voltages in major maintenance areas.
GLP features	Early maintenance feedback (EMF) for continuous tracking of instrument usage with user-settable limits and feedback messages. Electronic records of maintenance and errors
Housing	All materials recyclable
Metering device	Metering device in high pressure flow path

Performance Specifications (G7167A)
Table 4 Agilent 1260 Infinity Multisampler (G7167A) Performance Specifications

Type	Specification	Comment
Injection range for Single-needle instruments	Default: 0.1 – 100 μL in 0.1 μL increments; optional: 20 μL or 40 μL (using optional 40 μL analytical head	Up to 600 bar using 100 μL (default) or optional 40 μL analytical head
	0.1 – 500 μL or 900 μL in 0.1 μL increments (using 900 μL analytical head)	Pressure range up to 400 bar due to 900 μL analytical head
	0.1 – 120 μL in 0.1 μL increments with 1290 Infinity large volume injection kit (hardware modification required) G4216-68711 0.1 – 500 μL or 1500 μL in 0.1 μL increments with 100 μL upgrade kit (hardware modification required) G7167-68711	Pressure range up to 600 bar Multi-draw modus (Injection into needle-seat capillary)
Injection range for Dual-needle instruments	Default: 0.1 – 100 μL in 0.1 μL increments; optional: 20 μL or 40 μL (using 100 μL analytical head)	Up to 600 bar using 100 μL analytical head
	Up to 900 μL in 0.1 μL increments depending on installed loop size	Up to 600 bar using 100 μL analytical head
Precision for Single-needle instruments	<0.15 % RSD or SD <10 nL, whatever is greater	Measured caffeine
Precision for Dual-needle instruments	<0.2 % RSD or SD <10 nL, whatever is greater	Measured caffeine
Pressure range	Up to 600 bar (G7167A)	Max pressure for basic instrument
Sample viscosity range	0.2 – 5 cp
Sample capacity	1H Drawer up to 8 drawers and 16 positions Shallow well plates (MTP)	Max. 6144/1536 samples (384MTP/96)
	2H Drawer up to 4 drawers and 8 positions MTP, deep well plates, vials, Eppendorf	3072 samples, 432 vials (2 mL)
	3H Drawer up to 2 drawers and 4 positions MTP, deep well plates, vials up to 6 mL, Eppendorf	1536 samples, 60 vials (6 mL), 384 vials (1 mL), 216 vials (2 mL)
Injection cycle time	<10 s using following standard conditions: Default draw speed: 100 μL/min	Using standard Single-needle setup
	Default eject speed: 400 μL/min Injection volume: 1 μL	Time between 2 injections is not mechanically limited, time delay depends on communication speed of software, OS or network connections
Carry Over	<0.003 % (30 ppm) Multisampler Standard and Dual Needle <0.0009 % (9 ppm) Multisampler Multiwash	Using the following conditions: • Column: Agilent Pursuit XRs 3 C18, 2.0 x 50 mm • Mobile phase: • A: 0.1 % TFA in water • B: 0.1 % TFA in Acetonitrile • Isocratic : % B=40 % • Flow rate: 0.5 mL/min • Temperature: 25 °C • Wavelength: 257 nm • Sample: 1200 ng/μL Chlorhexidine (dissolved with mobile phase A), 1 μL injected and measured on G4212A DAD • Wash solution: H2O with 0.1 % TFA (3 s)
Multiwash	Outer needle wash and seat backflush for carryover reduction with up to 3 different solvents
Control and data evaluation	Agilent Open Lab CDS	A.02.01 or above (A.02.02 supports Sample Entry UI)
	MassHunter QQQ	B.07.00 SP11 or above
	MassHunter QTOF	B.05.01 SP31 or above
	Lab Advisor	B.02.05 or above
	ICF for 3rd party SW control	A.02.01 or above
	LC and CE Drivers	A.02.10 or above
Local Control	Agilent Instant Pilot (G4208A)	B.02.17 or above (currently not supported/official release 2015)
Communications	Controller-area network (CAN), Local Area Network (LAN) ERI: ready, start, stop and shut-down signals
Safety and maintenance	Extensive support for troubleshooting and maintenance is provided by the Instant Pilot, Agilent Lab Advisor, and the Chromatography Data System. Safety-related features are leak detection, safe leak handling, leak output signal for shutdown of pumping system, and low voltages in major maintenance areas
GLP features	Early maintenance feedback (EMF) for continuous tracking of instrument usage with user-settable limits and feedback messages. Electronic records of maintenance and errors.
Housing	All materials recyclable
Metering device	Metering device in high pressure flow path

P

Type	Specification	Comment
Injection range	Default: 0.1 – 100 μL in 0.1 μL increments	Up to 600 bar using 100 μL
	Default: 0.1 – 250 μL or 1000 μL in 0.1 μL increments with Multidraw upgrade kit (Bio-inert) (G5667-68711	Pressure range up to 400 bar Multi-draw mode (Injection into needle-seat capillary)
Precision	<0.15 % RSD or SD <10 nL, whatever is greater	Measured caffeine
Pressure range	Up to 600 bar	Max pressure for basic instrument
Sample viscosity range	0.2 – 5 cp
Sample capacity	1H Drawer up to 8 drawers and 16 positions Shallow well plates (MTP)	Max. 6144/1536 samples (384MTP/96)
	2H Drawer up to 4 drawers and 8 positions MTP, deep well plates, vials, Eppendorf	3072 samples, 432 vials (2 mL)
	3H Drawer up to 2 drawers and 4 positions MTP, deep well plates, vials up to 6 mL, Eppendorf	1536 samples, 60 vials (6 mL), 384 vials (1 mL), 216 vials (2 mL)
Injection cycle time	<10 s using following standard conditions: Default draw speed: 100 μL/min	Using standard Single-needle setup
	Default eject speed: 400 μL/min Injection volume: 1 μL	Time between 2 injections is not mechanically limited, time delay depends on communication speed of software, OS or network connections
Carry Over	<0.003 % (30 ppm) Multisampler Standard <0.0009 % (9 ppm) Multisampler Multiwash	Using the following conditions: • Column: Agilent Pursuit XRs 3 C18, 2.0 x 50 mm • Mobile phase: • A: 0.1 % TFA in water • B: 0.1 % TFA in Acetonitrile • Isocratic : % B=40 % • Flow rate: 0.5 mL/min • Temperature: ambient • Wavelength: 257 nm • Sample: 1200 ng/μL Chlorhexidine (dissolved with mobile phase A), 1 μL injected and measured on G4212A DAD • Wash solution: H2O with 0.1 % TFA (3 s)
Multiwash	Outer needle wash and seat backflush for carryover reduction with up to 3 different solvents
Materials in flow path	Titanium, gold, PTFE, PEEK, ceramic	Upstream of sample-introduction
	PEEK, ceramic	Downstream of sample-introduction
Control and data evaluation	Agilent Open Lab CDS	A.02.01 or above (A.02.02 supports Sample Entry UI)
	MassHunter QQQ	B.07.00 SP11 or above
	MassHunter QTOF	B.05.01 SP31 or above
	Lab Advisor	B.02.05 or above
	ICF for 3rd party SW control	A.02.01 or above
	LC and CE Drivers	A.02.10 or above
Local Control	Agilent Instant Pilot (G4208A)	B.02.17 or above (currently not supported/official release 2015)
Communications	Controller-area network (CAN), Local Area Network (LAN), USB ERI: ready, start, stop and shut-down signals
Safety and maintenance	Extensive support for troubleshooting and maintenance is provided by the Instant Pilot, Agilent Lab Advisor, and the Chromatography Data System. Safety-related features are leak detection, safe leak handling, leak output signal for shutdown of pumping system, and low voltages in major maintenance areas.
GLP features	Early maintenance feedback (EMF) for continuous tracking of instrument usage with user-settable limits and feedback messages. Electronic records of maintenance and errors.
Housing	All materials recyclable.
Metering device	Metering device in high pressure flow path

Performance Specifications G5668A
Table 5 Agilent 1260 Infinity II Bio-inert Multisampler (G5668A) Performance Specifications

Type	Specification	Comment
Injection range	Default: 0.1 – 100 μL in 0.1 μL increments	Up to 600 bar using 100 μL
	Default: 0.1 – 250 μL or 1000 μL in 0.1 μL increments with Multidraw upgrade kit (Bio-inert) (G5667-68711	Pressure range up to 400 bar Multi-draw mode (Injection into needle-seat capillary)
Precision	<0.15 % RSD or SD <10 nL, whatever is greater	Measured caffeine
Pressure range	Up to 600 bar	Max pressure for basic instrument
Sample viscosity range	0.2 – 5 cp
Sample capacity	1H Drawer up to 8 drawers and 16 positions Shallow well plates (MTP)	Max. 6144/1536 samples (384MTP/96)
	2H Drawer up to 4 drawers and 8 positions MTP, deep well plates, vials, Eppendorf	3072 samples, 432 vials (2 mL)
	3H Drawer up to 2 drawers and 4 positions MTP, deep well plates, vials up to 6 mL, Eppendorf	1536 samples, 60 vials (6 mL), 384 vials (1 mL), 216 vials (2 mL)
Injection cycle time	<10 s using following standard conditions: Default draw speed: 100 μL/min	Using standard Single-needle setup
	Default eject speed: 400 μL/min Injection volume: 1 μL	Time between 2 injections is not mechanically limited, time delay depends on communication speed of software, OS or network connections
Carry Over	<0.003 % (30 ppm) Multisampler Standard <0.0009 % (9 ppm) Multisampler Multiwash	Using the following conditions: • Column: Agilent Pursuit XRs 3 C18, 2.0 x 50 mm • Mobile phase: • A: 0.1 % TFA in water • B: 0.1 % TFA in Acetonitrile • Isocratic : % B=40 % • Flow rate: 0.5 mL/min • Temperature: ambient • Wavelength: 257 nm • Sample: 1200 ng/μL Chlorhexidine (dissolved with mobile phase A), 1 μL injected and measured on G4212A DAD • Wash solution: H2O with 0.1 % TFA (3 s)
Multiwash	Outer needle wash and seat backflush for carryover reduction with up to 3 different solvents
Materials in flow path	Titanium, gold, PTFE, PEEK, ceramic	Upstream of sample-introduction
	PEEK, ceramic	Downstream of sample-introduction
Control and data evaluation	Agilent Open Lab CDS	A.02.01 or above (A.02.02 supports Sample Entry UI)
	MassHunter QQQ	B.07.00 SP11 or above
	MassHunter QTOF	B.05.01 SP31 or above
	Lab Advisor	B.02.05 or above
	ICF for 3rd party SW control	A.02.01 or above
	LC and CE Drivers	A.02.10 or above
Local Control	Agilent Instant Pilot (G4208A)	B.02.17 or above (currently not supported/official release 2015)
Communications	Controller-area network (CAN), Local Area Network (LAN), USB ERI: ready, start, stop and shut-down signals
Safety and maintenance	Extensive support for troubleshooting and maintenance is provided by the Instant Pilot, Agilent Lab Advisor, and the Chromatography Data System. Safety-related features are leak detection, safe leak handling, leak output signal for shutdown of pumping system, and low voltages in major maintenance areas.
GLP features	Early maintenance feedback (EMF) for continuous tracking of instrument usage with user-settable limits and feedback messages. Electronic records of maintenance and errors.
Housing	All materials recyclable.
Metering device	Metering device in high pressure flow path

Physical Specifications of the Sample Cooler
Table 6 Physical Specification of the Sample Cooler

Type	Specification	Comments
Weight	< 6 kg
Dimensions (height × width × depth)	205 mm x 340 mm x 370 mm
Refrigerant gas	HFC-134a (0.042 kg)	Ozone depletion potential (ODP) = 0
Supply voltage	24 VDC (nominal)
Current	10 A max.
Ambient operating temperature	4 – 40 ° C (39.2 – 104 ° F)
Ambient non-operating temperature	-40 – 70 ° C (-20 – 158 ° F)
Operating altitude	Up to 3000 m (9842 ft)
Non-operating altitude	Up to 4600 m (15091 ft)
Safety standards: IEC, EN, CSA, UL	Installation category II, Pollution degree 2	For indoor use only.
ISM Classification	ISM Group 1 Class B	According to CISPR 11

Table 7 Performance Specifications Agilent 1290 Sample Cooler

Type	Specifications
Operating principle	High performance, low-energy consumption micro-compressor based cooler with ozone-friendly HFC-134a coolant (42 g), user-upgradable.
Temperature range	from 4 °C to 5 °C below ambient
Temperature settable	from 4 – 40 °C in 1 ° increments
Temperature accuracy (<25 °C, <50 % r.H.)	2 °C to 6 °C at a setpoint of 4 °C

NOS.	Parts No.	Description
1	G7110B  1260 Infinity II等度泵（大压力 600 bar。包括等度泵 、色谱柱、连接毛细管、溶剂柜、溶剂瓶和 CAN 电缆。）	1260 Infinity II Quaternary Pump
2	G7110B  001  液相工具包（液相色谱系统工具包。包括运行和维护安捷伦 1200 Infinity 系列液相色 谱系统所需要的工具。）	HPLC System Tool Kit, for Agilent 1260/1290 Infinity II LC
3	G7110B  032 主动阀套件	Active Inlet Valve (AIV)
4	G7110B 030 泵头密封垫清洗装置	Active Seal Wash
5	G1328C  1260 Infinity 手动进样器。包括 600 bar 的手动进样阀、20 μL样品瓶和固定支架。	1260 Series Manual Injector. Includes Rheodyne 7725 manual injection valve, 20 ul sample loop and mounting stand.
6	G7111A  1260 Infinity II四元梯度泵含在线脱气机（四元泵。大压力 400 bar。包括内置的四通道脱气单元。包括四元泵、连接毛细管、溶剂柜和 CAN 电缆。）	1260 Infinity II Quaternary Pump VL, maximum pressure 400bar. Includes quaternary pump, column, connecting capillaries, solvent cabinet, solvent bottles and CAN cable.
7	G7111A  001  液相工具包（液相色谱系统工具包。包括运行和维护安捷伦 1200 Infinity 系列液相色 谱系统所需要的工具。）	HPLC System Tool Kit, for Agilent 1260/1290 Infinity II LC
8	G7111A 032 主动阀套件	Active Inlet Valve (AIV)
9	G7111A 030 泵头密封垫清洗装置	Active Seal Wash
10	G7111B  1260 Infinity II四元梯度泵含在线脱气机（1260 Infinity II 四元泵，大压力 600 bar。包括四元泵 、连接毛细管、溶剂柜、溶剂瓶和 CAN 电缆。）	1260 Infinity II Quaternary Pump VL, maximum pressure 600bar. Includes quaternary pump, column, connecting capillaries, solvent cabinet, solvent bottles and CAN cable.
11	G7111B  001  液相工具包（液相色谱系统工具包。包括运行和维护安捷伦 1200 Infinity 系列液相色 谱系统所需要的工具。）	HPLC System Tool Kit, for Agilent 1260/1290 Infinity II LC
12	G7111B 032 主动阀套件	Active Inlet Valve (AIV)
13	G7111B 030 泵头密封垫清洗装置	Active Seal Wash
14	G7111B 093 色谱柱	Agilent Poroshell 120 EC-C18 4.6x100mm, 2.7um
15	G7122A 1260 Infi nity II 脱气机	1260 Infi nity II Degasser 4 channels; up to 10 mL/min fl ow; 12mL internal volume per channel
16	G7129A 1260 Infinity II 样品瓶进样器                                            (1260 Infinity II 样品瓶进样器，耐压达 600 bar。包括  100 μL 的计量装置以及 100 μL 的样品定量环，带集成进样针清洗口 。包括 2 个抽屉，每个抽屉可容纳 66 个样品瓶 (2 mL)	1260 Infinity II Vialsampler for use up to 600 bar. Includes 100 uL metering device and a 100 uL sample loop plus integrated needle flush port. Includes 2 drawers each for 66 vials (2 mL).
17	G7167-60005 温控器	Infinity II Sample Cooler
18	G7129A 1260 ICC 063集成式柱温箱 可容纳 2 根色谱柱，加热体积6 μL。)	1260 Thermostatted Column Compartment
19	G7116A 1260 Infinity II 容量柱温箱 可容纳 2 根色谱柱，加热体积 7 μL。)	10 degrees below ambient to 85 °C; up to four 30 cm columns; up to four individual Infi nityLab Quick-Connect heat exchangers; optional valve drive for Infi nityLab Quick Change valve heads (up to 600 bar and up to 4-column selection without re-plumbing)
20	G7167A 1260 Infinity II Multisampler，耐压达 600 bar，用于孔板和单个样品容器。包括 2 个样品抽屉、2 个 54 样品瓶容器 、个进样针清洗口、100 μL 计量装置和样品定量环。	1260 Infinity II Multisampler
21	G7117C 1260 Infinity II 二极管阵列检测器 HS。适用于灵敏度的快 速多波长光谱分析。数据采集速率达 120 Hz。用于流通池和灯的 RFID  标签。包括 10 mm 标准大光强卡套式流通池，体积1 μL	5410是为快速离心少量样品而设计的。外形精巧，运行时声音极低，具备离心机所需性能：Short- spin 瞬时离心功能.
22	G7121A  1260 Infinity II 荧光检测器（适用于可编程单波长检测（激发和发 射），数据采集速率达 74 Hz。包括标准流通池，8μL）	1260 Infinity II Variable Wavelength Detector
23	G7121B  1260 Infinity II 荧光检测器（适用于多波长检测，可在线采集 激发和发射光谱，采集速率达 148 Hz。包括标准流通池，8μL）	1260 Infinity II Variable Wavelength Detector
24	G7162A 1260 Infinity II 示差折光检测器。数据采集速率达 72 H z，配备集成式 8 μL 标准流通池	1260 Infinity II Refractive Index Detector
25	G4260B  蒸发光散射检测器	Agilent 1260 Infinity ELSD
26	ELSD模拟输出电缆线	38x-ELSD Analogue Output Cable
27	M8301AA 工作站数据处理系统	OpenLAB CDS ChemStation Workstation
28	M8500AA 工作站采样系统	OpenLAB CDS Inst. Driver for Agilent LC
29	M8410AA  OpenLAB CDS 工作站软件
30	M8410AA         001 液相色谱仪连接许可
31	M8410AA         005 3D UV/DAD 连接许可
32	5063-6591  手拧PEEK接头，1/16英寸，10/包	PEEK finger-tight 1/16 in, 10PK
33	0890-1763  PEEK管	1/16"od 0.007"id (0.18mm) 1.5m PEEK tbng
34	8710-1930 塑料管线切割器	Plastic and PEEK tubing cutter
35	5182-0714  2mL广口螺纹口玻璃瓶、透明，100个/包	Vial,screw,2ml,clr,cert,100PK
36	5182-0727  广口，无隔垫螺纹口瓶盖，用于2 mL 样品瓶，100个/包	Green color screw caps  100/PK
37	5182-0731  PTFE/红色硅橡胶乳白色隔垫，100/包	Septa, PTFE/red silicone, 8.7mm 100/pk
38	5063-6589 柱塞杆密封垫，石墨填充的PTFE（反相),(G1310A，G1311A，G1312A，G1376A，G2226A，1120，1220，G1310B，G1311B，G1312B，G1311C，G1312C，G4303A）	Plunger seal for 1100/1200 and 1050 2/PK
39	01018-22707 过滤白头,5/包	PTFE Frits 5PK
40	01018-60025	Solvent inlet filter, stainless steel
41	693970-902T 分析型液相色谱住，带色谱柱 ID（InfinityLab Poroshell 120 色谱柱可在主流液相色谱系统压力范围内实现稳定的分离度分离，分析速度可比传统 5µm 方法快 5 倍）	InfinityLab Poroshell 120 EC-C18，4.6×150 mm，4μm
42	990967-902 XDB-C18色谱柱      （温度上限：60℃， pH 围:2.0-9.0）	XDB-C18 Analytical HPLC Col 4.6 x250
43	820950-925 保护柱芯，4/包	Eclipse XDB-C18 4.6x12.5,5u Grd Car 4/PK
44	820999-901 保护柱卡套	High Perf. ZORBAX Guard Fittings Kit
45	SYS-LC-1260 硬件认证	LC 1260 System
46	SYS-LC-1260     6N9 硬件IQ认证  （安装验证）	Enterprise Qualification IQ
47	SYS-LC-1260     6J9 硬件OQ认证（操作验证）	Enterprise Qualification OQ      企业版操作认证
48	SYS-SW-OLAB-E 软件认证	OpenLAB CDS WorkStation
49
50	SYS-SW-OLAB-E   6N9 软件IQ认证（安装验证）	Enterprise Qualification IQ
51	SYS-SW-OLAB-E   6J9 软件OQ认证（操作验证）	Enterprise Qualification OQ

Type Specification Comments Weight 14.7 kg (32 lbs) Dimensions (height × width × depth) 180 x 396 x 436 mm (7.1 x 15.6 x 17.2 inches) Line voltage 100 – 240 V~, ± 10 % Wide-ranging capability Line frequency 50 or 60 Hz, ± 5 % Power consumption 80 VA, 65 W Ambient operating temperature 4–55 °C (39–131 °F) Ambient non-operating temperature -40 – 70 °C (-40 – 158 °F) Humidity < 95 % r.h. at 40 °C (104 °F) Non-condensing Operating altitude Up to 3000 m (9842 ft) Non-operating altitude Up to 4600 m (15092 ft) For storing the module Safety standards: IEC, EN, CSA, UL Installation category II, Pollution degree 2 For indoor use only. ISM Classification ISM Group 1 Class B According to CISPR 11

您留言咨询的信息，系统会以短信、邮件、微信三种方式同时通知客户。